⚡ EV Support Hub / Practical EV Guides
EV charging connectors

CCS2 DC vs Type 2 AC Charging: Key Differences

Comparison illustration of a CCS2 DC fast-charging connector and a Type 2 AC charging connector
The DC fast-charging connector is CCS2, which combines the Type 2 interface with two additional large DC power contacts. The separate Type 2 connector shown is for AC charging.

Technical terms at a glance

Type 2: AC chargingCCS2 connector: DC fast chargingOn-board charger (OBC)EVSE power (kW)

Published by EV Support Hub · Practical technical guide

Scope: This guide is for general education. Vehicle specifications, battery limits, charging performance and service procedures vary by model. Use the relevant owner's manual and manufacturer service information for vehicle-specific decisions.

Type 2 AC and CCS2 DC are two common charging interfaces used by electric vehicles in India and other markets. They are related but serve different charging methods. Type 2 supplies alternating current (AC) to the vehicle, where the onboard charger converts it to DC for the battery. CCS2 supports DC fast charging, allowing the external charging equipment to supply controlled DC power to the vehicle's battery system.

1. Type 2 AC charging

With AC charging, the charging station supplies AC power and the vehicle's onboard charger (OBC) performs AC-to-DC conversion. The maximum AC charging rate is limited by the vehicle's OBC rating, the available supply and the charging equipment. A higher-rated AC station does not make a vehicle charge faster than its own OBC and electrical limits allow.

2. CCS2 DC fast charging

CCS2 combines the Type 2 AC interface with two additional large DC power contacts. During DC charging, conversion is performed by the off-board charger. The vehicle and charger communicate and manage the charging session within the limits of the battery, vehicle and charger.

3. Main differences

FeatureType 2 ACCCS2 DC
Power supplied to vehicleACDC
Where conversion happensInside vehicle OBCInside external DC charger
Typical useHome, workplace and destination chargingPublic rapid/fast charging
Vehicle limitOBC rating and supply limitsVehicle DC acceptance and battery limits
Charging timeUsually longer for the same energy amountCan be faster when vehicle and charger support higher power

4. Why an AC charger rating may not equal vehicle charging power

Consider a vehicle with a 6.6 kW onboard charger connected to a compatible 7.4 kW AC charging point. The vehicle is generally limited by its 6.6 kW OBC rating, and actual power may be lower due to supply voltage, current limits, temperature and conversion losses. A 3.3 kW OBC would not accept 7.4 kW simply because the station can provide it.

5. Estimate AC charging time

Ideal charging time (hours) = energy required (kWh) ÷ charging power (kW)

For example, adding 13.2 kWh at a steady 6.6 kW would take 13.2 ÷ 6.6 = 2 hours in an ideal calculation. Actual time can be longer because of conversion losses, power variation, battery temperature and charging limits.

6. Why DC charging power changes during a session

DC charging power is not necessarily constant from low SOC to high SOC. The vehicle's battery management system may request less power as SOC rises or when battery temperature is outside its preferred operating range. The charger also has its own voltage, current and power limits. This changing power profile is commonly called the charging curve or power taper.

Therefore, dividing the energy required by the charger's maximum advertised power can significantly understate the actual session time. Use vehicle-specific charging information when planning a trip.

7. Connector and compatibility checks

8. Basic charging fault observations

If a session does not start, check the station display or app for an error, confirm the connector is fully inserted and locked, and follow the vehicle/network instructions. If the same issue occurs repeatedly, record the charger ID, time, vehicle warning and session details and contact the charging network or authorised vehicle support. Do not open the charger or attempt high-voltage repairs.

Frequently asked questions

Can a Type 2 AC vehicle use a CCS2 DC charger?

Only if the vehicle is equipped for the corresponding DC charging method and connector. A Type 2 AC inlet alone does not provide CCS2 DC capability.

Does a 60 kW DC charger always charge at 60 kW?

No. Actual power depends on the vehicle's DC acceptance limit, battery SOC and temperature, charger capability and site power conditions.

Is AC charging slower because of the onboard charger?

The onboard charger rating is one important limit. AC supply limits and conversion losses also affect the rate.

Can I use any CCS2 charger with any CCS2 vehicle?

Connector compatibility is necessary but not the only consideration. Check voltage/current compatibility, network access, charger status and the vehicle manufacturer's guidance.

Further reading and tools

Use EV Support Hub's charging station search and charging-time calculator. Confirm live availability and vehicle compatibility with the charging network before starting a journey.